Midwest

• Easy to install, one screw installation takes less than one minute
• Extremely rigid, will not move once tightened due to taper and angled cuts
• Can be used for both right handed and left handed shooters
• Will fit any AR series rifle with standard front sight housing
• MCTAR-01G2 has two mil-spec picatinny rails with two anti-rotation sling swivel sockets

Weight 2.1oz

 
• Mounting hardware included
• Will fit AR series handguards with large or small holes
• Hard coat anodized 6061 aluminum construction
• In most circumstances you will be able to use standard heat shields after installation

WILL NOT FIT GEN2 SS HANDGUARDS.

Weight .7oz

• Mounting hardware included
• Will fit plastic "GI type" AR series handguards with large or small holes
• Hard coat anodized 6061 aluminum construction
• In most circumstances you will be able to use standard heat shields after installation

WILL NOT FIT GEN2 SS HANDGUARDS
WILL NOT FIT M-Lok HAND GUARDS
WILL NOT FIT KEYMOD HAND GUARDS

• Constructed of 6061 aluminum, hard coat anodized to provide a lifetime of service

Weight .9oz

• Constructed of 6061 aluminum, hard coat anodized to provide a lifetime of service

Weight .5oz

• Constructed of 6061 aluminum, hard coat anodized to provide a lifetime of service

Weight .9oz

• Constructed of 6061 aluminum, hard coat anodized to provide a lifetime of service

Weight 1.6oz

• Work well in all types of configurations, including single point, two point or three point tactical slings
• Easy, no gunsmith installation, no need for special tools or removal of buffer tube
• Constructed of 6061 aluminum and hard coat anodized for a lifetime of service

Weight .5oz

• Has two loops that accept HK type clasps, fully ambidextrous
• Easy, no gunsmith installation, no need for special tools or removal of buffer tube
• Constructed from 4140 steel, phosphate finished for a lifetime of service
• 100% made in the U.S.A.
• Lifetime Warranty

Weight 1.6oz

• Work well in all types of configurations, including single point, two point or three point tactical slings
• Easy, no gunsmith installation, no need for special tools or removal of buffer tube
• Constructed of 6061 aluminum and hard coat anodized for a lifetime of service

Weight .7oz

• No gunsmith drop-in installation, installs like factory plastic handguards!
• Gen2 design with four anti-rotation QD sockets for push button swivels
• Incredibly light weight, extremely solid lock-up with monolithic type continuous top rail
• High quality 1913 mil spec rails, T-marked for location
• MCTAR-17G2 Carbine... Length: 7 inches ... Weight: 7.5 oz.
• Constructed from 6061 aluminum hard coat anodized
• Only compatible with Round hand guard caps
• 100% Made in the U.SA. with a lifetime warranty
  

• 100% made in the U.S.A. with Lifetime Warranty
• Installs on a GI barrel nut, not included with hand guard
• Complete install in minutes, removal of delta ring is required
• Four anti-rotation QD sockets for push button swivels
• High quality 1913 mil-spec rails, T-marked for accessory location
• Incredibly lightweight, extremely solid lock-up with monolithic type continuous top rail
• Billet machined from 6061 aluminum and hard coat anodized.
• Carbine ... Length 7 inches ... Weight 9.0 oz.
• Piston compatible Works with most well known piston systems including STAG, CMMG, ADAMS and
• Smith & Wesson to name a few. (Will not work with Osprey Systems)

• 100% made in the U.S.A. with Lifetime Warranty
• Complete install in minutes, removal of delta ring is required
• Clamps directly to a GI Barrel nut
• Upper hand guard is notched for a carbine length A2 front sight
• Four anti-rotation QD sockets for push button swivels
• High quality 1913 mil-spec rails, T-marked for accessory location
• Incredibly lightweight, extremely solid lock-up with monolithic type continuous top rail
• Billet machined from 6061 aluminum and hard coat anodized.
• MCTAR-20XG2: Extended Length Carbine ... Length 12.5 inches ... Weight 14.6 oz.
• The MCTAR-20XG2 extended length carbine model will not work with gas piston systems.

• 100% made in the U.S.A. with Lifetime Warranty
• Installs on a GI barrel nut, not included with hand guard
• Complete install in minutes, removal of delta ring is required
• Four anti-rotation QD sockets for push button swivels
• High quality 1913 mil-spec rails, T-marked for accessory location
• Incredibly lightweight, extremely solid lock-up with monolithic type continuous top rail
• Billet machined from 6061 aluminum and hard coat anodized.
• Mid-Length ... Length 9 inches ... Weight 11.3 oz.
• Piston compatible Works with most well known piston systems including STAG, CMMG, ADAMS and
• Smith & Wesson to name a few. (Will not work with Osprey Systems)

• 100% made in the U.S.A. with Lifetime Warranty
• Installs on a GI barrel nut, not included with hand guard
• Complete install in minutes, removal of delta ring is required
• Four anti-rotation QD sockets for push button swivels
• High quality 1913 mil-spec rails, T-marked for accessory location
• Incredibly lightweight, extremely solid lock-up with monolithic type continuous top rail
• Billet machined from 6061 aluminum and hard coat anodized.
• MCTAR-22G2: Rifle ... Length 12.5 inches ... Weight 14.6 oz.
• Piston compatible Works with most well known piston systems including STAG, CMMG, ADAMS and
• Smith & Wesson to name a few. (Will not work with Osprey Systems).

• Work well in all types of configurations, including single point, two point or three point tactical slings
• Easy, no gunsmith installation, no need for special tools or removal of buffer tube
• Constructed of 6061 aluminum and hard coat anodized for a lifetime of service

Weight 1.3oz

• Work well in all types of configurations, including single point, two point or three point tactical slings
• Easy, no gunsmith installation, no need for special tools or removal of buffer tube
• Constructed of 6061 aluminum and hard coat anodized for a lifetime of service

Weight 3oz

• Uses standard A2 front sight post
• Super smooth ball bearing pivot detent automatically locks in the raised position with locking detent
• Constructed of 6061 aluminum, hard coat anodized for a lifetime of service
• Gas block model is for a gun with a railed gas block that is lower than the upper
• Gas block mount model folds to front
• Also works with DPMS Sportical

• Uses standard A2 front sight post
• Super smooth ball bearing pivot detent automatically locks in the raised position with locking detent
• Constructed of 6061 aluminum, hard coat anodized for a lifetime of service
• Rail height model is for mounting on gas blocks or handguards that are the same height as the upper
• Rail mount model folds to rear
  

Anyone who has cleaned an AR-series rifle knows how hard it is to maintain and clean the gas tube, to ensure reliability. Midwest Industries has come up with an innovative, practical and cost effective solution: the MCT-AR-GTB.

• Made from high quality materials
• Use it again and again with great results
• Works on 16 or 20 inch barrel rifles
• Comes in a bag for buttstock storage
• Goes down gas tube without kinking, unlike a pipe cleaner
• Simply remove the brush from the bag, straighten the shank and feed the brush down the gas tube
• This brush takes the hassle out of cleaning this critical part of the rifle.

• Constructed from 4140 steel
• 1.810" long to cover the taper pin holes if FSB is removed
• Low profile design will fit under most commercially available hand guards
• Secures to barrel with three set screws

• Constructed from 4140 steel
• 1.810" long to cover the taper pin holes if FSB is removed
• Low profile design will fit under most commercially available hand guards
• Secures to the barrel with three set screws
  

• Constructed from 4140 steel
• Low profile design will fit under most commercially available handguards
• Secures to the barrel with three set screws

• Sits only .4375" when folded
• Extremely low profile dual aperture design
• Locking detent with large surface area for maximum strength
• Same ball detent battle proven design of #MCTAR-ERS
• Lock detent button with stepped down turns, to provide a surface you can grab onto if your hands are muddy or wet.
• Micro style windage knob featuring the same MOA adjustments as the standard M-16: .65 MOA on M-4type rifles / .49 MOA on M4 Type rifles
• Made in U.S.A. with Lifetime Warranty

Weight 1.3oz

• Constructed from 4140 steel
• For .750 diameter barrels
• 1913 Spec Rail machined to same height as A-4 uppers
• Weighs 6.0 oz

• Made to fit the Ruger® 10/22® receivers and clones
• Uses factory mounting holes
• Hard coat anodized 6061 aluminum construction, for a lifetime of service
• Matte Black Finish
• Weight 1.6 ounces with screws
• 4.650" AOL Length
• Picatinny Rail
• Midwest Industries Lifetime Warranty

Ruger®, PC Carbine®, 10/22 TakeDown®, 10/22®, and Ruger® Precision® are trademarks of Sturm, Ruger & Company, Inc.

• Made to fit the Ruger® 10/22® receivers and clones
• Uses factory mounting holes
• Anodized 6061 Aluminum construction, for a lifetime of service
• Matte Silver Finish
• Weight 1.6 ounces with screws
• 4.650 OAL Length
• Picatinny Rail
• Midwest Industries Lifetime Warranty

Ruger®, PC9™ Carbine, 10/22 TakeDown®, 10/22®, and Ruger Precision® are trademarks of Sturm, Ruger & Company, Inc.

Features

• Lightweight design with a low profile
• Mounting screws and wrench included
• Weight 2 oz installed
• Construction from 6061 Aluminum, Type 3 Hard Coat Anodized for a lifetime of service
• Fully dehorned for a non-abrasive, comfortable feel
• MI Lifetime Warranty
• 100% Made in America - Keeps America Working
• US Patent Pending

• Two Piece Drop-In Handguard
• Incredibly Lightweight (Supplied M-LOK(TM) compatible Rail adds .5 oz)
• MI-17M Carbine 5.0 oz
• Solid Lock up
• Drop-in, no gunsmith installation, installs in minutes like factory handguards!
• Five anti rotation QD socket locations for QD sling swivels
• Monolithic type continuous top rail
• MIL-STD 1913 top rail
• Only compatible with Round hand guard caps
• Lifetime Warranty
• 100% Made in the U.S.A.

M-LOK(TM) is a trademark of Magpul Industries Corp

• Two Piece Drop-In Handguard
• Incredibly Lightweight (Supplied M-LOK(TM) compatible Rail adds .5 oz)
• Weighs 6.6 oz
• Solid Lock up!
• Drop-in, no gunsmith installation, installs in minutes like factory handguards!
• Five anti rotation QD socket locations for QD sling swivels
• Monolithic type continuous top railMIL-STD 1913 top rail
• Only compatible with Triangle han
• d guard caps
• Lifetime Warranty
• 100% Made in the U.S.A.

M-LOK(TM) is a trademark of Magpul Industries Corp

• Two Piece Drop-In Handguard
• Incredibly Lightweight (Supplied M-LOK(TM) compatible Rail adds .5 oz)
• Weight 8.5 oz
• Solid Lock up!
• Drop-in, no gunsmith installation, installs in minutes like factory handguards!
• Five anti rotation QD socket locations for QD sling swivels
• Monolithic type continuous top rail
• MIL-STD 1913 top rail
• Only compatible with Triangle hand guard caps
• Lifetime Warranty
• 100% Made in the U.S.A.

M-LOK(TM) is a trademark of Magpul Industries Corp